Nancy and Shelly,
I received my showerhead & filters
last night and they works great! The filters workvery well. I have
dermatitis and the chlorine in my water was really irritating my skin. It was so
nice to take a shower last night and actually enjoy it!
EASY INSTALLATION INSTRUCTIONS FOR THE ULTIMATE® DUAL SHOWER FILTER
santé Inc. Phoenix, AZ 85085 623-266-7409 or 623-266-7429
EASY INSTALLATION INSTRUCTIONS FOR THE ULTIMATE®
DOUBLE SHOWER FILTER
FEMALE END OF METAL ELBOW
TEFLON (PLUMBERS) TAPE INCLUDED GOES ON ALL THREADED MALE
2. SHOWER FILTER WITH SIDE REMOVED SO YOU CAN SEE
THE REFILL BEFORE INSTALLATION.
3. METAL ELBOW
– THE FIRST PART TO SCREW ONTO THE WALL PIPE.
4. TWO WASHERS;
ONE SIDE FLAT THE OTHER SIDE ROUNDED.
5. THE FLAT
SIDE OF THE WASHER GOES INTO THE FEMALE END OF THE ELBOW.
6. THE FLAT
SIDE OF THE SECOND WASHER GOES INTO THE FEMALE END OF THE SHOWER FILTER. THE
SHOWER FILTER SCREWS ONTO THE MALE END OF THE ELBOW.
SHOWERHEAD SCREWS ONTO THE MALE END OF THE SHOWER FILTER. Following the above should complete the
installation. Below find additional information.
Step 1. Most shower heads are easily removed without using tools. Tools are not needed to install this
shower filter. IMPORTANT: This is installed one piece at a time at
the shower, Not at the kitchen
Note 1: Please
read step 5A below if you are using a Pre-Filter. It would go on first. A Pre-Filter is not used with a hand held
shower wand head
Note 2. You
should not have to remove the side
pieces or the filters when installing. Only
when replacing the refills once a year
3. Everything with threads is called the
male end. Teflon tape (included) goes on every male end. Three wraps should be
enough. THE FLAT END OF THE
WASHER FITS INTO THE METAL ELBOW. THIS IS THE END WITH THE METAL RING ON
IT. THE WASHERS GO IN THE FEMALE ENDS
WITH FLAT END IN OR THEY WILL NOT FIT. THE WASHERS ARE BEVELED ON ONE END TO LOCK
INTO THE MALE END WHEN THE FEMALE ENDS ARE SCREWED ONTO THE MALE ENDS. IF THE
WASHER IS IN THE WRONG WAY THE MALE END WON’T SCREW IN PROPERLY.
****Step 1A. THIS
IS THE FIRST STEP IN INSTALLING THE PARTS. Place the washer into the female end of the elbow and
screw the elbow onto the wall pipe
****Step 2A The Dual "ULTIMATE”® Shower Filter screws onto
the curved metal elbow. The
female end of the elbow has a revolving top on it so if you hold the curved elbow
in the middle you can turn the female revolving part (top). Make sure the flat
end of the washer is in the female side.
****Step 3A The showerhead is installed last. Please
understand, we are not responsible for the installation. If installed correctly
it will not leak. Call us only if a part is missing or is broken.
ONLY TIGHTEN THE SHOWER FILTER AND SHOWERHEAD BY HAND, OVERTIGHTENING WILL
CAUSE THE CENTER UNIT TO BREAK
****Step 4A. Screw on the
shower head. Remember no tools are
DO NOT OVERTIGHTEN!
Step 5A. If you are installing a Pre-Filter; it will go on the
shower pipe first, followed by the shower filter and lastly the shower head
*** Replacing the filters for the first
time: When you make a filter change and
reinstall the filters. Please note that each filter has 3 lines across. The
long center line matches to a raised piece on the male end that has the small
"O” ring on it. This notched piece fits
into the small grove on the center piece. Use #630 silicon Lube which is
available from us for $4.99 a tube on the "O” rings.
IF YOU ARE NOT
HANDY THEN CALL A HANDYMAN, PLUMBER, FRIEND OR SOMEONE WHO CAN PUT THIS UNIT ON
FOR YOU. IT IS VERY EASY TO INSTALL BUT SOME PEOPLE ARE NOT GOOD WITH PLUMBING